Name: XPA DR 2
SKU: 2753
Availability: InStock

Circuit Topology	A fully modular, fully differential, fully balanced audio power amplifier with a high-efficiency switch mode power supply (SMPS), independent, fully discrete, dual differential, high current, short signal path Class A/B amplifier modules, Optimized Class H™ power supply topology, and microprocessor-controlled fault protection.
Power Output (both channels driven)	550 watts RMS, per channel, into 8 Ohms, at <0.1% THD. 800 watts RMS, per channel, into 4 Ohms, at <0.1% THD.
Power Bandwidth (at rated power; 8 Ohm load)	20 Hz to 20 kHz (+ / – 0.1 dB).
Broad Band Frequency Response	20 Hz to 50 kHz +0/-2 dB.
THD + noise	< 0.008%; at 100 watts RMS; 1 kHz; 8 Ohms.
Signal to Noise Ratio (8 Ohm load)	> 120 dB; ref FTC rated power; unbalanced input (A-weighted). > 96 dB; ref 1 watt; unbalanced input (A-weighted).
Minimum Recommended Load Impedance (per channel)	4 Ohms (which equals one 4 Ohm load or two paralleled 8 Ohm loads).
Damping Factor (8 Ohm load)	> 500.
Input Sensitivity (for rated power; 8 Ohm load)	2.1 V.
Gain	29 dB.
Maximum Power Consumption	1,700 watts. Note: The values shown refer to the amount of power the amplifier would consume while playing test tones continuously, on all channels, at full power, into a load bank. Therefore they are not at all characteristic of what you would expect when playing music or the sound track from a movie. Normal audio signals are dynamic, so the amount of power they require from second to second varies widely, and the average is far lower than this. With normal content, even playing very loudly, one of the amplifiers will consume far less power than indicated in the chart, so these values should not be considered to be a circuit requirement for normal operation consume while playing test tones continuously, on all channels, at full power, into a load bank. Therefore they are not at all characteristic of what you would expect when playing music or the sound track from a movie. Normal audio signals are dynamic, so the amount of power they require from second to second varies widely, and the average is far lower than this. With normal content, even playing very loudly, one of Emotiva’s amplifiers will consume far less power than indicated in the chart, so these values should not be considered to be a circuit requirement for normal operation.
Input Impedance	33 kOhms (balanced). 23.5 kOhms (unbalanced).
Input Connections:	Unbalanced (RCA); balanced (XLR); one each, per channel, user selectable.
Speaker Output Connections:	Audiophile grade, gold plated, 5-way binding posts.
Trigger	Trigger Input: 5 – 12 V (AC or DC); <10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 120 mA.
Power Requirements	Between 100 VAC and 250 VAC @ 50 / 60 Hz (automatically detected).
Front Panel Controls and Indicators	Standby: push button (halo ring changes color to indicate Standby or On). Status LEDs: one per channel; blue. Status LEDs change to red to indicate a fault condition.
Rear Panel Controls	AC Power switch: rocker switch (switches AC main power). Status LEDs switch: disables front panel Status LEDs and dims Standby button halo. Input selector switches (one per channel): metal toggle switches; select between balanced and unbalanced inputs. Circuit Breaker: press button to reset circuit breaker.
Protection	The XPA-DR2 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions.
Dimensions	17” wide x 8” high x 19” deep (unboxed; including feet). 17” wide x 7” high x 19” deep (unboxed; without feet). 24-1/2” wide x 12” high x 24-3/4” deep (boxed).
Weight	42.5 lbs (unboxed). 47.5 lbs (boxed).

Reviews

There are no reviews yet.

Be the first to review “XPA DR 2”

XPA DR 2

Channel: 2; Class A/B; Output: 550 watts/ Channel RMS @ 8 Ohms & 800 watts/ Channel RMS 4 Ohms

Reviews

Related products

XPA DR 3

A7+

XPA 11 GEN 3

XPA 5 GEN 3

Channel: 2; Class A/B; Output: 550 watts/ Channel RMS @ 8 Ohms &
800 watts/ Channel RMS 4 Ohms